8/22/2018

EUCLEIA TanScan S7 All Key Lost Programming for Honda Civic

EUCLEIA TanScan S7 is not only a automotive diagnostic device,but also can perform key programming for vehicle immobilizer system.Here i share the guide on how to use EUCLEIA TanScan S7 to do all keys lost programming for Honda Civic.



Description:
Drivers lost all keys ,technicians get new key ready ,key notice keep showing on dashboard,car can not be started.


Vehicle Information:
Model:Honda Civic
Year:2010.09
VIN:LVHFA1615A50***
Engine Type:R18A1



Operation Devices:
EUCLEIA TabScan S7
EUCLEIA TabScan S8


Procedures:
Connect EUCLEIA TabScan S7 with car and select “Service”---“Immobliser”


Select “HONDA”---Immobliser


Select "Manual"

Type 2(4G)

Select "All keys lost".

Insert new key and turn on ignition, input the key amount required according to the notice.
Turn on/off ignition until device remind the IMMO light is on or not, If yes then click ok.



Once remind Program success, restart ignition ,the IMMO light is off .

Summary:
For IMMO function ,pls input all values carefully to make process under control.
EUCLEIA diagnostic scanner supported lot of maintenance functions, usually the process is little complicated ,just do as recommend step by step , then you will get what you want.


8/19/2018

EUCLEIA TabScan S7 Reset EPB for Renault Koleos 2010

Topic:How to use EUCLEIA TabScan S7 to reset EPB for Renault Koleos 2010


Vehicle Information:

Model:Renault KOLEOS
Year:2010.01
VIN:VF1VYRTE1AC3***

Operation Devices:
EUCLEIA TabScan S7
EUCLEIA TabScan S8


Procedures:
Put into P gear, press EPB,and release hand brake.

Connect with EUCLEI TabScan S7 and select “Service”-“EPB Reset”


Select “RENAULT”- ”Koleos“;

Select “Perform”.
Confirm tips and Select “OK”.
This time can hear the branch pump of rear brake pad is ting for seconds, then show “success”. click OK.
Install the new brake pad and click “Release”.

This time can hear the branch pump of rear brake pad is ting for seconds, then show “success”. click OK.


Operation ended ,quite software and press EPB button to make hand park working .

Summary:
EUCLEIA diagnostic scanner supported lot of maintenance functions, usually the process is little complicated ,just do as recommend step by step , then you will get what you want.

8/16/2018

EUCLEIA TabScan S7 Reset EPB for Volvo XC60 2011

This article show a operations on how to use EUCLEIA TabScan S7 to reset EPB Volvo XC60 2011.



Vehicle Information:

Model:Volvo XC60 T5
Year:2011.06
Engine Type:B4204T7
YV1DZ475XC224****

Operation Devices:
EUCLEIA TabScan S7
EUCLEIA TabScan S8


Operations:
Turn on the ignition switch, select P gear, press the EPB switch to release the handbrake.

Connect EUCLEIA S7 to vehicle and enter “Service” menu to select “EPB Reset”

Choose “Volvo”
Choose “XC60”



Choose “Replace the rear brake pads”

Click “OK” according to prompt
At this point, the brake pump will be retracted, and then the ring of rear wheel brake pump will be heard for a few seconds, waiting for the page to jump before replacing the new brake pad to the car.

Lease replace brake pad for the two rear wheels!

After the replacement is completed, click "confirm" and the brake pump will be released, and the ring of motor will be heard for a few seconds, waiting for the page to jump and then click "confirm".


Replace brake pad success!


Click “OK” button and exit the system. Turn off and then turn on the ignition switch and press EPB button. Completed.


Summary:
For EPB Reset usually need release the handbrake ,don’t forget this . EUCLEIA diagnostic scanner supported lot of maintenance functions, usually the process is little complicated ,just do as recommend step by step , then you will get what you want.

8/13/2018

How to use EUCLEIA TabScan S7 Reset EPB for Audi A8 2011

Here comes the guide on how to reset EPB for Audi A8 2011 by EUCLEIA TabScan S7.Hope it helps!



Vehicle Information:
Audi A8 2011
Manufacturer:Audi AG Neckarsulm
VIN:WAURGB4H3CN0****
Type:A8L 3.0 TFSI quattro


Products for Operation:

EUCLEIA TabScan S7
EUCLEIA TabScan S8


Procedures:

Connect EUCLEIA TabScan S7 to vehicle and enter the “Service” menu to select “EPB Reset”



Select “Audi”-->”A8”



Select “A8(D3)”
Select “Replacement of brake pads”

According to notes to release handbrake, then click “Yes”, at this time the rear brake pump motor will be heard for a few seconds to be retracted. After the retraction is completed, install the new brake pad according to the notification, then click “ok”.

The brake pump is released,please wait...
Lease replace brake pad for the two rear wheels!

At this time rear brake pump will ring for few seconds, after the branch pump is released , click ok.

Replace brake pad success!
All operation completed, quite system, press electrical handbrake button to make handbrake work, reset EPB completed.
Please exit the system,turn off and then turn on the ignition switch,completed.

Notes:
Please do remember release the handbrake once Reset EPB.

Article from EUCLEIA TabScan S7 S8 Tech,How to use EUCLEIA TabScan S7 Reset EPB for Audi A8 2011